HomeSpot HQ

Your Home Maintenance Partner

driveway

A Step-By-Step Guide To Repairing An Asphalt Driveway All By Yourself

by

how to repair an asphalt driveway yourselfIt’s not nice watching your asphalt driveway fall apart, but what else can you do? At first you just notice a crack then it slowly becomes a lot worse. As soon as you have a big hole in your driveway you will need to do something about it.

Luckily you don’t need to call someone out and spend a huge amount of money because you can repair it yourself. It’s not exactly a hard job, so don’t worry about it. Let’s look at what you need to know before you get going. You should have it finished in no time.

Measure Your Hole

Before you start doing anything you will need to get out your measuring tape to work out how big your hole is. This is important because if you don’t buy enough asphalt filler you will mess everything up. If the hole is less than two feet square you won’t need very much to fill it, so a normal 50b bag should usually be enough.

Use Stamped Concrete As An Affordable Way To Decorate Your Patio Floor

by

If you’re on a budget, a stamped concrete patio is affordable way to get the look of natural slate or limestone. It could also be made to mimic cobblestones, weathered wood, cracked earth and brick. The best part is that stamped concrete requires little maintenance since there is no grout that will get discolored or open up to let in grass and weed.

what is stamped concrete?What’s Stamped Concrete?

Stamped concrete is essentially a slab of concrete that has been embossed or textured. Usually completely by a contractor, the process involves:

  •  Pouring and smoothing the concrete
  •  Pressing a pattern into the surface before the concrete dries
  •  Adding color after the surface has been stamped. Some contractors add color to the concrete during the mixing stage.

Note: You should only hire a contractor who can provide examples of previous work.

Should You Do It Yourself?

Although you’ll want to enhance the look of your patio at the lowest possible cost, you should not attempt to do a stamped concrete patio yourself unless you’ve done it before. The process is quite simple, but since concrete is a complex medium to work with, you should get professional help if you want it done right. Some of the difficult parts of the process include:

  • Installation of the concrete base, which must be level and smooth.
  • Moving of the heavy concrete from one place to another.
  • Using specialty tools to shape and smooth the surface
  • Applying the stamps quickly before the concrete hardens

Keep in mind that concrete is permanent once it hardens. It’s possible to rent the concrete stamps, and even at a cost of $25 per stamp per day, you could save as much as 50 percent on the cost of professional installation. But keep in mind that you should have some knowledge of the process before you attempt to do it on your own.

Deicers for Driveways and Sidewalks

by

Preventing Ice

The best solution to keeping ice off of sidewalks and driveways is shoveling snow. As soon as the snow has stopped, shovel and sweep it away as a part of routine home maintenance. Ice on driveways and sidewalks most times comes from people and cars compacting the snow down.

There’s not much you can do about freezing rain. But take advantage of warmer days to clear ice with a metal shovel. It should break it up just enough to make shoveling possible.

Using a Deicer on a Driveway or Sidewalk

There is no one best product when it comes to deicers. And it is tough to evaluate products since there is no law keeping the labels honest. So a company can claim “pet safe” or “yard safe” even though it is no better than most chloride products.

Prevent ice on the driveway and sidewalks

Concrete Spalling and Repair

by

Concrete spalling is one of those terms not found in everyday language, but I will bet you’ve seen this problem numerous times. Concrete spalling is where the surface of a driveway or sidewalk erodes away. This condition is most common in northern areas where ice is common during the winter.

concrete spalling and repairSources of Concrete Spalling

The freeze-thaw cycles and deicing chemicals used to keep a driveway clear create a nasty combo for unsealed cement. Water from melted snow seeps into the capillaries of the cement re-freezes. The freezing process puts a lot of pressure on the cement and starts to create the spalling effect. The deicing chemicals, most commonly rock salt, can create the same effect. If too much salt is applied, it begins to collect within the top layers of the cement. It will then crystallize and put pressure on the concrete. The last source of concrete spalling comes from the rebar. If it is exposed to air and moisture, it will begin to corrode and more pressure is applied to the concrete.

Prevention

All of the sources of the problem stem from water issues. If you can prevent water from seeping into the concrete, then you can prevent spalling. The best solution is to use a concrete sealer. Apply a concrete sealer after letting a new driveway settle for 30 days. From that point forward reapply a sealer every two years.

To apply a sealer, measure the square footage of the concrete and buy the appropriate amount of product. Next, clean the surface of dirt and other debris. The temperature will probably need to be above freezing (depends on the product) and the surface free of water. Pick a day when there is no rain or high winds in the forecast. Apply the sealer evenly while avoiding puddling. The sealant will need at least a couple hours to settle.

Repair Concrete Spalling

Repair the concrete on driveways and sidewalks to increase curb appeal. Concrete spalling is best repaired with polymer modified cementitious coating. The cement component will give the cured product a hard finish that blends in with the rest of the driveway or sidewalk. The polymer component gives it an adhesive trait that helps the compound fill in the hole. However, the surface must be prepped for the product to work. Otherwise, your home’s cement will be in the same problematic scenario again next year.

Use an acid wash if the surface is loose. After the surface is clean, apply the primer to give the surface adhesion. Use a broom to apply the primer evenly.

Make sure the repair product is the same strength and mix up the solution in a bucket. Then pour the mixture over the spalled areas. Use a squeegee to evenly distribute the material. Wait 24 hours for the mixture to harden and visually inspect. You can apply a second coat if there are still depressions. After letting is completely settle for week, apply a cement sealer to give it long lasting protection.

If you would like to see a video on the subject, check out the Concrete Network here.